When I received my Baofeng UV-5R, I also received a programming cable so I downloaded the free CHIRP software for programming the HT. When I looked at all the radio options, I saw it also programmed the three other radios that I also have, The Kenwood TM-281, Yaesu 857, and FT-8900.
- Baofeng Uv-9r Programming Software
- Baofeng Uv-7r Programming Software Update
- Baofeng Uv-9r Programming Software Download
- Baofeng Uv-7r Programming Software Free
- Baofeng Uv-7r Programming Software Downloads
- Baofeng Uv-7r Programming Software
The software can also be called 'UV6UV7'. UV67UVUVCPS.exe, UV82CPS.exe, UV82CPSVIPv130413.exe, UV82US2S25VIP.exe and UV8VIPCPS.exe are the most common filenames for this program's installer. UV-6 UV-7 Series lies within System Utilities, more precisely Device Assistants. Our antivirus scan shows that this download is safe. Here you will find user manuals, device drivers and softwares for a wide range of our products. UV-5R EX Chirp Programming Engilsh UV-5R EX Programming Guideline. Baofeng UV-5R EX User Manual Version 2.0 Baofeng UV-5R EX User Manual EN + DE UV-5R Series Manual IT UV-82X3.
I ordered the cable for the FT-8900 and learned how to program the radio using the Chirp software.
When I first ordered the cable to program the Yaesu FT-8900R, I didn’t realize just how to work it. So, like I do with my Kenwood and Baofeng, I plugged in the cable and turned on the radio…..
The Yaesu doesn’t work that way. The radio immediately went into transmit until I turned it off again!
I returned the cable as defective and ordered another one. When I received it, the new cable did the same thing. Then I talked to another ham on one of the local repeaters who corrected me in how to use it.
- To put the 8900 into clone mode, you have to
- turn off the radio,
- plug in the cable, then,
- while pushing and holding the V/M button,
- turn it on.
- Rotate the right frequency knob until you see
- “Clone Start”
- Press the Menu Key
- (the small square button in the middle)
The first time you use a radio with Chirp, you have to have Chirp download from the radio.
In chirp,
Select “Radio”
“Download from Radio”
Choose the correct COM port
Choose “Yaesu” for Vendor
Baofeng Uv-9r Programming Software
Choose FT-8900 for the radio.
This is where your timing is critical. It takes practice…. You only have about 1/2 to 1 second to press both buttons
In Chirp, press OK
Baofeng Uv-7r Programming Software Update
THEN
On they 8900, press V/M immediately after.
…. and wait…………
My desktop (not the fastest computer in the world) takes 3 to 5 minutes to transfer to and from the Yaesu.
It works much more quickly on my Kenwood TM-281 and Baofeng radios which only have up to 127 memory locations, but the 8900 has 800 memory locations, so it takes 5 to 8 times as long to transfer.
I have a copy of ADMS software for programming the Yaesus, but it is so old, it is on a floppy. I don’t have a floppy or a CD drive, so I can’t use it.
Chirp doesn’t allow you to change any specialty frequencies such as the Hyper-Memories and range frequencies, but those can easily be set by hand on the radio.
One of the best features I like about Chirp is it’s ability to download frequencies from RepeaterBook.com. It has a proximity setting, so I set it to 75 miles and downloaded all repeaters. The frequencies, offsets and tone requirements were all added in just seconds.
Baofeng Uv-9r Programming Software Download
Afterwards, I checked each of the repeaters early in the morning while propagation was still good and deleted the ones I couldn’t hit.
Because it has so many memories available, I also included all the FRS, GMRS, MURS, and WX frequencies so I can monitor any of them as desired.
Baofeng Uv-7r Programming Software Free
Because this radio banks the memories so I can scan certain groups, I can program the local public service frequencies into one section and the ham into another. I can choose which bank to scan so I it’s pretty versatile.
Baofeng Uv-7r Programming Software Downloads
For my review of the Marvogo USB Programming Cable I use, check out my review article at N4PGW.org/Marvogo-USB-Programming-Cable-Review
Baofeng Uv-7r Programming Software
You can buy either the FT-8900R and the Marvogo USB programming cable from Amazon.com. Just click the links or images below: